How to deactivate if we don't want to use it? New Visitors are encouraged to read our. The participant continues to send refresh messages requesting more sessions until the server can adequately fulfill the request. When the load is reduced on a participant, it sends a message to the server to release the shared sessions. Proceed with update flash activation key? If the feature is tiered, the licensed capacities have to match. Advanced Endpoint Assessment License 8. Although the system does not require this key for basic operation, some advanced features, such as failover, depend on the permanent activation key in order to operate correctly.
To ease the management of time-based licenses and receive the maximum advantage of combining their duration when possible, always make sure to use separate time-based activation keys for each feature and tiered capacity. Examples The following example sets the shared secret, changes the refresh interval and port, configures a backup server, and enables this unit as the shared licensing server on the inside interface and dmz interface. The active license is shared between the failover units. With the 10,000-session license, the total combined sessions can be 10,000, but the maximum number of Phone Proxy sessions is 5000. If the new license does not get rid of failover, it will work just fine.
The permanent key must be replaced with another permanent key with fewer features. Upon rebooting, you will then notice that your files have disappeared and will be unable to boot up and will be stuck with this output. It also describes the available licenses for each model. Hosts that initiate traffic between Business and Home are also not counted towards the limit. For a shared licensing server, you need to buy the same shared licensing server license for both units.
Upgrading the License for a Failover Pair If you need to upgrade the license on a failover pair, you might have some amount of downtime depending on whether the license requires a reload. Step2: Power off the appliance and then power it on. You have to enter each key as a separate process. The running key defaults to the permanent key value of 10 sessions. However, the new key will deactivate the original time-based license if it enables 2500 AnyConnect Premium Peers instead or also adds the Intercompany Media Engine feature. Cisco's answer was that I dont need to worry about it. Does temp lincese doesn't show up except time based activity? If I am missing something, please let me know and I can try to find a better answer for you.
You will then need to apply the licence to the device. Step 2 activation-key key Example: active config activation-key 0xd11b3d48 0xa80a4c0a 0x48e0fd1c 0xb0443480 0x843fc490 Installs the new license on the active unit. After obtaining the Product Authorization Keys, register them on Cisco. Configuring a Shared License This section describes how to configure the shared licensing server and participants. This license is applied by simply using the activation-key command.
You can only use one temporary license at a time. License Notes lists footnotes for the tables in the. Thus, if you wish to revert, you must overwrite the current permanent key with another permanent key with fewer features. Even though these core features do not require an explicit activation key, one usually comes installed anyway. In addition to the permanent activation key, you can install one or more time-based keys to enable certain features for a limited period of time. If you do not need to reload, then follow the instead of this procedure.
This time it wasn't great they only sent email instead of calling and the process was rough and inexact. I know for failover both devices must be exactly the same at first i thougth that the AnyConnect license would be lost when upgrading to SecPlus. How to check whether box is ssl enabled or not for additional licesnes using any command? Entering a New Activation Key This section describes how to enter a new activation key. This is only for Anyconnect Premium. On the standby unit: Step 3 activation-key key Example: standby activation-key 0xc125727f 0x903de1ee 0x8c838928 0x92dc84d4 0x003a2ba0 Installs the new license on the standby unit. I went 4 levels in to the cli guide for my version 9.
This may take a few minutes. So we upgrade that one to a SecPlus License to enable failover posibilities and we bought a new 5510 also with a SecPlus license. The standby unit remains in a pseudo-standby state. Even for a shared licensing server? A reboot is not needed. This may take a few minutes. When the active license expires, you need to manually activate the new one.