Bought a new one from amazon, installed it, but the problem is still there. Dealer said it was normal and nothing to worry about. So I inferred the motor was faulty. The vehicle was not repaired. I'll take it to the dealer and see what they say.
Do you know anything else I should try? I believe Chevrolet should recall this vehicle and replace the wiper motor rather than plug the hole as they did originally. Lower the seat to the normal position. It only works sometimes, early in the morning when the temperature is low. Attempt to move the seat. If it is not software version 21. As I tried to loose the shaft the motor and gearing in the motor felt like it broke free. Mit anderen Worten, das Auto ist reif für den Schrottplatz.
There is a 10mm nut at the end of the cranking shaft. Dealership says they fixd it but upon pick up the problem still exists. Aktuelle Studien zeigen, dass Tacho-Manipulation eine der häufigsten Betrugsformen im Verkaufsprozess eines Gebrauchtwagens ist. A voltmeter could track this down in a few minutes. I tried to take it off to try and get the shaft to move without the stress or weight of the seat.
It is fuse number 3, 20A yellow , located on the left side as you're looking it, in the slot immediately forward of the fuse puller tool. I seem to be experiencing the same sort of issue except it is the front of the power seat wont move. Since the seat belt retractor is part of the seat back, this may also cause the driver not to be properly retained to the seat in the event of a collision. The cause of the failure had not been determined. It's design and mounting location causes it to have to support the weight of the driver as he enters or exits the vehicle.
The dealer informed the consumer he would receive new blades and that would take care of the problem, however those blades didn't work any better. I tried prying up on the front silver worm gear as well as on the back side just like you did in this video. They stutter and sometimes stop in mid stroke, unless on high speed. Old bulbs do not always appear to have burned or broken elements, but have replaced them anyway for safety sake. Driver does not know of the problem until tyring to use the wipers. Verify that the fuse is not open.
On the 2008 Equinox, this fuse is in the fuse block under the hood. So I inferred the motor was faulty. You can rate this solution and show your appreciation Posted on Sep 03, 2010 unfortunately the electric seats from all of the car builders have never been able to fix the problems that plage them since their creation they are known for switchs going out motors and drives failing start by making sure you have power to all of these you will need to trace power from your fuse panel using a test light or volt meter next look check to make sure that the tracks on the seat are free of debri and clean then you will have to take the track apart and check the drive gears and cables to make sure they are not damaged Sep 02, 2014 Brake light problem - if bulbs and fuses 34 and 43 in rear fuse panel are good, then only other possibility are the circuit boards where all the tail lights are located. It looked like it holds the plastic part that moves up and down. This happened again on the way home from the dealer.
I already made sure all my cd cases, floor mats, empty pop bottles and old french fries were out from under there and it made no difference. My vehicle was also under a gmpp extended warranty. I tried to upload a pic take from my iPad, we'll see if it worked. If the relay is clicking, then its command side coil is being energized. But slowly this stopped and then I figured out that by wiggling the motor connector would make it work, but that too stopped working. Connect the electrical connectors to the new seat module.
Okay, I figured it out. Shortly later, the wipers began to malfunction while on intermittent. When the main menu is displayed on the Tech 2, verify the software version that is installed in the Tech 2. Windshield wipers don't work when turned on, or come on when switch is in the off position. In some cases this resets the system computer and all starts working.
It is my only vehicle and I am still paying dearly for it but lately cannot even use it as it remains in one dealership after another at my expense. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do a job properly and safely. If you have the memory seat module, it may be involved, but I don't have access to my schematics at the moment. Reposition the seat switch bezel and install the three retaining screws. Occasionally they moved while the vehicle was in motion. The vehicle now has 04000 kilometers and the wiper circuit board needs to be replaced. Either a power door lock actuator or the power door lock switch.