Be sure to work with a cool engine and confirm the cooling system lacks pressure before opening the cooling system. Once detached from the mass air flow sensor, pull the duct off the throttle housing. If you treasure your car, make sure to use only high performance grade parts to maintain it. Be sure that it is flush with the radiator. Did not see new or old parts.
When a radiator begins to fail, you'll notice that the car tends to overheat at high engine speed, such as driving on the highway. Makes it hard to understand which part you're highlighting. Remove the radiator cooling fan. Just be sure to remove the negative battery terminal, not the positive. Remove the air box beside the battery a 10 mm bolt and the relay is a four prong square box bolted on the frame with two 8mm bolts www. When replacing the engine side cooling fan you will want to work with the engine cold. You will want to pull the hose off, while rocking it back and forth.
The engine cooling fan is located at the front center of M62 8-cylinder engines beneath the intake air ducts. Make sure to check your engine when it is cold for an accurate reading. Be sure to pull the retaining clips out until they rest at the stop. Figure 15 Separate the viscous clutch from the fan blade. With your vehicle specifics handy, Give The Pelican Parts parts specialists a call at 1-888-280-7799.
Then install the expansion rivets. For those contemplating this - have patience. You will have to remove the intake air ducts that attach to the mass air flow sensor to access the fan. The clip for that particular hose is facing toward the right frame rail. It is a good idea to inspect your radiator hoses every time you're under the hood. After cooling off, the coolant is transferred back to the engine.
Just be sure to remove the negative battery terminal, not the positive. Animals love its sweet taste, so even a spilling a small amount on your garage floor can end up in the dog's stomach pretty quickly. By adding antifreeze to a highly functional radiator, you're able to not only enhance engine performance, but also reduce the probability of engine failure at the same time. All parts were replaced and supposedly new. If we get a chance to perform the procedure, we will be sure to document it. Function test: Use extreme caution when the engine is running. When the engine is cool or at operating temperature, the fan clutch partially disengages the engine's radiator cooling fan, located at the front of the water pump and driven by the engine drive belt.
Then, remove the coolant hoses from the thermostat and water pump housing. Shop our assortment of X5 radiators today and gain access to trustworthy advice provided by helpful staff, as well as free battery charging and engine diagnostic testing. To replace the radiator hoses, use a flathead screwdriver to lever out the coolant hose retaining clips. The hoses have been attached to the thermostat for quite a while and may not come off easily. Remove the lower coolant hose from the radiator by pulling it straight off.
Ok, Is it really that easy? Figure 11 Working at the left side of the radiator, remove the two T25 Torx fasteners green arrows. It should be closed or read less than 0. If you don't replace the radiator when needed, the engine would overheat, the pistons would break, thereby causing permanent damage to your vehicle. Then remove the automatic transmission cooler bracket from the radiator and transfer it over to the new radiator. Thanks J June 3, 2015 Followup from the Pelican Staff: We don't currently have that tech article. The price estimated is exclusive of taxes and fees. Was on my way driving out of town.
Release the sensor, replace and connect the shaft. For location and diagnosis, refer to Electrical Diagnosis. December 21, 2017 Followup from the Pelican Staff: Thanks for the additional info and feedback. Then, install the cooling fan and fill and bleed the cooling system. These vehicles use 2 360 mm 14. Once the hose moves off the radiator slightly, you can use a flathead screwdriver to gently lever the hose off while pulling it. April 18, 2018 Followup from the Pelican Staff: Thanks for the additional info and feedback.
Radiator hose clamps may also loosen, which could cause a leak, so make sure to check their condition as well. The engine of your car operates via a chain of moving parts. Once the hose moves off the radiator slightly, you can use a flathead screwdriver to gently lever the hose off while pulling. Disengaging the fan saves power, since the engine does not have to fully drive the fan. Mix the coolant with distilled water so that you have a combination of 50% coolant and 50% water.