1998 isuzu rodeo manual. 1998 ISUZU RODEO Factory Technical Service Bulletin 2019-03-11

1998 isuzu rodeo manual

1998 Isuzu Rodeo Specs

1998 isuzu rodeo manual

Always replace with new 7. Disconnect coil integrated module connector. Install two new O-rings to front housing. These modules are designed Data Link Connector to withstand normal current draws associated with vehicle operation. Install plate 11 , ball 10 and bearing collar 9. Push High—Low shift rod 13 through shift arm 14 and block 14.

Next

Isuzu Rodeo Service Repair Manual

1998 isuzu rodeo manual

Remove upper inner return spring 9. Raise the vehicle and support with suitable safety 10. Install transfer rear cover assembly 7 to transfer case assembly 8. You can find a complete list of accessories that can further enhance the performance of your engine. Tighten the stud nut until a torque of 1.

Next

ISUZU 1999 RODEO WORKSHOP MANUAL Pdf Download.

1998 isuzu rodeo manual

Remove lower ball joint by using remover J—29107. Therefore, it is most important to repair refrigerant leak when there is any leak found. Connect the high pressure charging hose of the manifold gauge to the high pressure side service valve of the vehicle. Install driver knee bolster reinforcement. Discharge and recover refrigerant f Refer to Refrigerant Recovery in this section. Lead is usually caused by: 8.

Next

ISUZU 1999 RODEO WORKSHOP MANUAL Pdf Download.

1998 isuzu rodeo manual

Locate cylinder with defective bearing by listening for abnormal noise that stops when spark plug is shorted out. Discard these used rubber parts and replace with new ones. Completely remove all lubricant and moisture from the bolts and the female-threaded surfaces of the parts to be joined. Remove detent ball, spring and plug 1. Vibration can be caused by an out—of—phase propeller shaft. Set the yoke in the arbor press with a piece of tube stock beneath it. Torque : 11 N·m 95 lb in 3.

Next

1998 Isuzu Rodeo Auto Repair Manual

1998 isuzu rodeo manual

When installing the steering column cover, be sure to 7. Use a spring pin remover to remove the spring pin 2 8. Retail Dealer Air conditioning S 3. Remove wheel and tire assembly. Refer to Front Inspection and Repair Propeller Shaft in this section. Remove torsion bar, refer to Torsion Bar in this section.

Next

ISUZU 1999 RODEO WORKSHOP MANUAL Pdf Download.

1998 isuzu rodeo manual

Make sure of the output conditions of each sensor. Check accelerator pedal for smooth Accelerator Linkage Lubrication operation and even pedal effort. Wire the power steering line to frame. Try Solution 3 after adjust the Were problems found? Install adjust bolt and seat, then turn the adjust bolt to marks 2. New Compressor Installation f Move serpentine belt tensioner to loose side using The new compressor is filled with 150cc 5. Remove four bolts and remove the crankshaft pulley 1.

Next

1998 Isuzu Rodeo Specs

1998 isuzu rodeo manual

Two weeks ago the engine started making noise and I took it to the dealership and was told I needed a new engine!! If the measured value is less than the specified limit, the detent spring must be replaced. Install 2 gaskets and spacer. If the bolt holes in the lock plate are not aligned with the corresponding holes in the nut, reverse the lock plate. Remove the parking brake cable from the trailing link. Mount a dial indicator with a magnetic base to the housing and indicate on the flange or head of screw. Remove pinion oil seal slinger.

Next

1998 Isuzu Rodeo Specs

1998 isuzu rodeo manual

Disconnect the battery ground cable. Remove the front propeller shaft. To install, follow the removal steps in the reverse order, 7. Disconnect the rear propeller shaft 1 from the 1. Remove the front propeller shaft.

Next

1998 Isuzu Rodeo Auto Repair Manual

1998 isuzu rodeo manual

Torque: 39N·m 29 lb ft 12. Remove ball retainer, ball guide and bellows. Tighten fixing bolt 1 of timing belt tensioner to the specified torque. Supplemental inhibitors or additives claiming to increase cooling capability that have not been specifically approved by Isuzu are not recommended for addition to the cooling system. Align the track on the ball 1 retainer with the window installation, check that the bellows is free from in the cage, and install the six balls into position. Remove snap ring from front axle case by using snap 10. Even though the seat is not height adjustable and may not suit everyone, the driver enjoys a commanding position.

Next